Cyber-Plus Evolution C109N is the new PC-based and touch screen control unit for the management of SEMI/FULLY AUTOMATIC compression, flexural, and splitting tensile tests on concrete and cement specim
“Servo-Plus Evolution” 8-channel servo-controlled graphic display control unit to provide fully automatic tests throughout all phases: data acquisition, display, processing, pace rate adjustment.
COMPRESSION TESTING MACHINE 1300 kN CAPACITY to test cylinders up to dia. 160x320 mm and cubes up to 150 mm side.
COMPRESSION TESTING MACHINE 1500 kN CAPACITY to test cubes up to 150 mm side and cylinders up to dia. 160x320 mm
COMPRESSION TESTING MACHINE 2000 kN CAPACITY “TESTED FOR HIGH STABILITY” to test cubes up to 200 mm side and cylinders up to dia. 160x320 mm
COMPRESSION TESTING MACHINE 3000 kN CAPACITY To test cubes up to 200 mm side and cylinders up to dia. 160x320 mm
COMPRESSION TESTING MACHINE 5000 kN CAPACITY to test cubes up to 300 mm side and cylinders up to dia. 250x500 mm
This is an easy to operate Compression testing machine. This compression testing machine has three kinds of scale and each has a full measure range.
Flexural testing machine, 50 kN capacity designed to test: paving slabs, flat blocks, roof tiles, floor tiles, terrazzo tiles, ceramics, bricks, masonry units, etc.
FLEXURAL TESTING MACHINE 150 kN CAPACITY To perform flexural tests on concrete beam specimens max. dimensions 150x150x600 (750) mm
To perform flexural tests on concrete beams max. dimensions 150x150x600/750 mm, flat blocks, flagstones, kerbs, tiles, slabs, masonry units, and any type of material having max. width 600 mm and max.
Used to cut concrete specimens and any type of construction material like blocks, tiles, pipes, rock cores etc.
Designed to grind and polish concrete cube and cylinder specimens, blocks, natural stones, rocks, ceramic materials etc. C299 is an Automated Version of the C298 Machine
Carry out non-destructive tests on concrete structures, indicates compressive strength.
It records directly the percentage of air enclosed in freshly mixed concrete by operating according to the air pressure principle.
Identical to mod. C196 but with built in automatic electric air compressor giving air pressure, and keeping it constant all along the test.
For the rapid determination of moisture content in wet cement and concrete. Ratio range: 0,35 to 0,70 water/cement.
Same to mod. C214 but with ratio range: 0,25 to 0,5 for low water cement ranges.
This Hardened Concrete Test Hammer can test the surface in a non- destructive manner. The Hardened Concrete Test Hammer is supplied with carrying case grinding stone and instructional manual.
This Rebar locator is used to detect the thickness of concrete covering layer and rebar diameter. It is an easy to use rebar locator.
For the determination of the consistency, the medium and high workability of fresh concrete. The slump is measured using the tamping rod having a graduated scale engraved in 1 cm increments.
The Vebé consistometer method is based on the same principle of the simple slump cone test method, for the determination of the workability of concrete, but it has the advantage of a mechanized action
These slump test cones are used to test fresh concrete. It is easy to use these Fresh Concrete testing slump cones.
Reusable heavy-duty steel split moulds are extremely sturdy and the inside surfaces are accurately machined.
These models of steel beam moulds are extremely sturdy and the inside surfaces are accurately machined.
The mould is used for casting specimens of cement aggregate combinations for measuring the potential expansive alkali reactivity.
Internal surface, base, top and bottom ring are accurately machined.
These models of steel cube and beams moulds are extremely sturdy and the inside surfaces are accurately machined. Nominal dimensions meet to EN 12390-1 requirements.
Portable electric Poker Vibrator suitable for the internal compaction of concrete specimens both in laboratory and in site.